XTi Series 4002
Product Overview
There’s no debate – when you choose Crown’s XTi 2 Series, you’re choosing one of the most powerful and innovative amplifiers on the market today. That’s because the all-new XTi 2 Series amps continue to set the standard for unmatched performance and value, delivering the goods night after night without breaking a sweat.
Product Details
 |
 |
 |
 |
|
| 2Ω Stereo (per ch.) | 700W | 1000W | 1600W | 3000W |
| 4Ω Stereo (per ch.) | 500W | 800W | 1200W | 2100W |
| 8Ω Stereo (per ch.) | 275W | 475W | 650W | 1200W |
| 8Ω Bridge-Mono | 1000W | 1600W | 2400W | 4200W |
| 4Ω Bridge-Mono | 1400W | 2000W | 3200W | 6000W |
- Peakx Plus™ Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
- Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
- 3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
- New system monitoring provides software visibility of AC line voltage and power supply temperature
- Integrated cast-aluminum handles for easy handling and enhanced durability
- Locking power cord clip provides a secure connection between the amplifier and power cord
- Updated HiQnet System Architect™ control software
- Increased number of presets to a total of 50; 49 of which are user definable
| Input EQ | 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed. |
| Crossover Filters | Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control. |
| Output EQ | 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed. |
| Delay | For signal alignment of driver; 50 mS of total delay. |
| SubHarmonic Synth | Takes the low-frequency content of the input signal and “synthesizes” a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type. |
| Peakx™ Plus Limiter | User defeatable limiter that allows users to control Threshold, Attack, and Release times. |
| Presets | 50 total presets, 49 of which are user-definable. |
| Sensitivity (for full rated power at 4 ohms) |
1.4 Vrms |
| Frequency Response (at 1 watt, 20 Hz – 20 kHz) | +0 dB, –1 dB |
| Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms) | XTi1002/2002/4002: 100 dB (A weighted) XTi6002: 103 dB (A weighted) |
| Total Harmonic Distortion (THD) | < 0.5% |
| Damping Factor 20 Hz to 1 kHz | > 500 |
| Crosstalk (below rated power) | 20 kHz – 1 kHz: > 70 db |
| Input Impedance (nominal) | 20k ohms balanced, 10k ohms unbalanced |
| Maximum Input Signal | +22 dBu typical |
| AC Line Voltage and Frequency Configurations | 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz |
| AC Line Current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch) |
XTi1002: 6.8A; no more than 38W at idle XTi2002: 8.3A; no more than 38W at idle XTi4002: 10.5A; no more than 38W at idle XTi6002: 15.3A; no more than 180W at idle |
| Operating Temperature | 0°C to 40°C at 95% relative humidity (non-condensing) |
| Level | Two front-panel rotary level controls, one for each channel |
| Power Switch | On/Off switch applies AC power to the amplifier |
| Sel/Prev/Next Buttons | Three buttons near the LCD screen that are used to access menu items and front panel lockout |
| LCD Screen | Backlit liquid crystal display that shows preset and processing status |
| Signal Indicator | Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs). |
| –10 Indicator | Green LED flashes when output signal exceeds -10 dB below clip. |
| –20 Indicator | Green LED flashes when output signal level exceeds -20 dB below clip. |
| Ready Indicator | Green LED, one per channel, illuminates when the amplifier is ready to produce audio. |
| Clip Indicator | Red LED, one per channel, turns on at the threshold of audible distortion |
| Temp Indicator | Red LED, one per channel, illuminates under excessive temperature conditions |
| Power Indicator | Blue LED illuminates when the amplifier has been turned on and has power |
| Input Connectors | XLR, one per channel |
| Link/Out Connector | Loop-thru signal from input connector for linking another amplifier, one per channel. |
| Output Connectors | Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors). |
| HiQnet™ USB Connector | Type B, connects to HiQnet™ network. |
| Chassis | Steel |
| Front Panel | Cast-aluminum |
| Cooling | Proportional speed fan with front-to-rear airflow. |
| Dimensions | XTi 1002/2002/4002: 19″ (W) x 3.5″ (H) x 12.25″ (D) XTi 6002: 19″ (W) x 3.5″ (H) x 16.2″ (D) |
| Net Weight | XTi 1002/2002/4002: 18.5 lbs (8.4kg) XTi 6002: 24.0 lbs (10.9kg) |
| Shipping Weight | XTi 1002/2002/4002: 21.5 lbs (9.8kg) XTi 6002: 30.0 lbs (13.6kg) |
No reviews yet. Add yours!
Your Review
You must be logged in to post a comment.